Sponsored Links

Sponsored Links

Page 3 of 3 FirstFirst 123
Results 21 to 26 of 26



  1. #21
    Contributor karpof's Avatar
    Join Date
    May 2013
    Posts
    15
    Sponsored Links
    Sponsored Links
    tried that version 2 m8, no work either.. what i have installed is just cfw either rebug 4.41 with multiman 4.40 or Rogero 4.40 version 1.03 with multiman 4.30 and 4.40 also tried Rogero_Manager_v8.2 with rogero.. is that enough to get ps3 up and running or am i forgeting to install something else ?

    is it worth downgrading back to OFW 3.55 then upgrading again to rebug 4.41 could my firmware be corrupt ? sometimes when i turn ps3 on it says files corrupt but when i let it go through fixing files it crashes at 19 % and wont finish repairing files either from xmb or safe mode .. thanx for your patience guys

    also if i have to go to 3.55 can i do it over rebug 4.41 ? cheers
    Last edited by karpof; 06-08-2013 at 03:13 PM Reason: Automerged Doublepost

  2. #22
    Senior Member daveshooter's Avatar
    Join Date
    Nov 2010
    Posts
    414
    Sponsored Links
    Sponsored Links
    Hello Bud, if its possible swap out your drive that's in that ps3, with a small drive just for working with, trust me when I say it helps not needing to format a drive when the ps3 has crashed and its lost the drive inside.

    In a nut shell you need to force manufacturing_updater_for_reset.self into the ps3 without trying to use the pup that the file came in, to reset the bd if that make sense.

    The instructions say you need your Ps3 on a working 3.55 firmware, but the ps3 I did was also on 4.41. I used the E3 to do in short this below.

    Remarry guide for 3.55 firmware from: http://www.ps3news.com/forums/ps3-ha...tml#post411024

    Related guide: http://www.ps3news.com/ps3-hacks-jai...ther-consoles/

    1. Have the console on a working 3.55 firmware

    2. Download the Remarry files (remarry-3.55.rar) and unpack to root of USM Mass Storage device. The following line is already changed from 1 to 0:
    Code:
         #---------------------------------------------
         # Install Systemsoftware
         #   0 = Žs‚‚‚
         #   1 = Žs‚‚
         #----------------------------------------------
         0
    This will make sure the drive init PUP is not installed, thus preventing RLOD because of syscon hashes on downgraded consoles.

    3. Download official firmware <=3.30 as drive init PUP and put it root of USB Mass Storage device

    Content of USB Mass Storage device should be thus be:
    Code:
                                               MD5:                               SHA1:                                      CRC32:     CRC16:
         Lv2diag.self                          C48E5EBFC00ABD89094CB73A2B0BEA59 / D229AC694910272DDEA9276B9FD4A2664800638C / C2D0A2B0 / 5327
         manufacturing_updater_for_reset.self  9E3C9024E9243478D21C78E1C9DF2376 / 922EA202CA2EA36EBF2B5054605E17409B9A56E6 / 93F18A95 / EA0D
         fdm_spu_module.self                   33E8D3C12349CFD203930FD0C237054D / F660FD6EBEB12DC7F52B4E707A1F0D1BD05DF9F3 / 85701A9B / B75B
         PS3UPDAT.PUP
         cfg/standalone.cfg
    4. Put the service mode JIG/dongle/PSGrade into port 0 (closest to the reader) and get into factory service mode.

    5. Put the created USB Mass Storage device from step 3 into port 0 (closest to the reader) and run.

    Drive Init Executing means it is starting the remarry process
    Drive Init Failed with big pink letters 'NG' (No Good!) means the process failed. Most likely solved by fixing the communication issue with the drive.

    6. After you run the initial remarry process, do not take it out of factory service mode.

    7. Put a BD movie disc in and run it on the PS3. (This restores your DRL files!)

    8. Then you can take it out of factory service mode.

    9. Launch as normal.
    Code:
    PUP INFO
    --------
    PUP file information
    Package version: 1
    Image version: 46136
    File count: 7
    Header length: 528
    Data length: 177740882
    PUP file hash : F2E908F18CEC6B344B5562D710797EBF4AC8CA03
        File 0
        Entry id: 0x100
        Filename : version.txt
        Data offset: 0x210
        Data length: 15
    File hash : BB0BD4B340519157CED7507196D63791FEAB0CD1
        File 1
        Entry id: 0x101
        Filename : license.xml
        Data offset: 0x21F
        Data length: 282723
    File hash : 11E2669ADBAEED4984BA1BA644CA54BCD1958346
        File 2
        Entry id: 0x103
        Filename : update_flags.txt
        Data offset: 0x45282
        Data length: 5
    File hash : FD7C893936FDFC668922BE6D119A462111B2BBDB
        File 3
        Entry id: 0x200
        Filename : ps3swu.self
        Data offset: 0x45287
        Data length: 5661656
    File hash : 05A938D262915A0BD9978A14A70380383A8F6F82
        File 4
        Entry id: 0x201
        Filename : vsh.tar
        Data offset: 0x5AB65F
        Data length: 10240
    File hash : D9B66E0D2845D71A67D76E7907AB06368CE61E08
        File 5
        Entry id: 0x202
        Filename : dots.txt
        Data offset: 0x5ADE5F
        Data length: 3
    File hash : 1AA4749D0EE0D0AE937FBF73BC4B9ACD352F732A
        File 6
        Entry id: 0x300
        Filename : update_files.tar
        Data offset: 0x5ADE62
        Data length: 171786240
    File hash : 7A643784FAFE2A91E1794BCBBFE43CB701B6E071
    Please Note if it displays this, Drive Init Executing means it is starting the remarry process. Drive Init Failed with big pink letters 'NG' (No Good!) means the process failed. Most likely solved by fixing the communication issue with the drive.

    Try 1st as it said this ti me and it still worked, go figure, lol

    Hope some, if not all helps.

  3. #23
    VIP Member JeoWay's Avatar
    Join Date
    Jun 2013
    Posts
    342
    Sponsored Links
    Sponsored Links
    Install a CFW (I suggest Rebug or Rogero 4.XX)
    Use multiMAN to place games on.
    Use homebrew such as emulators.

    The most important thing of all, have fun.

  4. #24
    Contributor karpof's Avatar
    Join Date
    May 2013
    Posts
    15

    daveshooter and JeoWay

    hi dave.

    4. Put the service mode JIG/dongle/PSGrade into port 0 (closest to the reader) and get into factory service mode.

    I don't have a JIG/dongle and my BD dont work to Put a BD movie disc in and run it on the PS3. (This restores your DRL files!)

    and jeoway: Multiman crashes, thats my prob. what emulaors will work ?

  5. #25
    Senior Member daveshooter's Avatar
    Join Date
    Nov 2010
    Posts
    414
    Sorry late reply, just to say I don't think you can fix your ps3 without some form of hardware.

  6. #26
    Senior Member hilongo's Avatar
    Join Date
    Oct 2010
    Posts
    167
    When you load a game from Multiman, it always gets you back to XMB... then you have to scroll up in the Game menu and you'll see a disc icon ...as if you were inserted a real disc... you then select that disc icon and the game should start!

    You are almost there... good luck!

    Happy gaming!

 

Sponsored Links

Page 3 of 3 FirstFirst 123
Affiliates - Contact Us - PS3 Downloads - Privacy Statement - Site Rules - Top - © 2014 PlayStation 3 News