Sponsored Links

Sponsored Links

Page 1 of 2 12 LastLast
Results 1 to 10 of 11



  1. #1
    Member k9inpoop's Avatar
    Join Date
    Oct 2010
    Posts
    83
    Sponsored Links

    [Answered] Help with Bricked Slim Ps3?

    Sponsored Links
    ok i bricked my ps3 SLIM going back to CEX from DEX a few weeks ago. i didn't know that i should not turn it off after i reflashed the flash from my back up using the multiMAN method and now it does the 5 quick beeps and just shuts down i have tried using a psp with ps3jig to get it into Factory/Service Mode but it just beeps still and won't go into it.

    i still have the back-ups of my root key, CEX-FLASH-NOR-FW3.55.NORBIN and 355DEX.EID0.NORBIN. if i get a e3 flasher limited can i unbrick the system or is it just a paper weight? if i can save the system can someone tell me how to do it using the e3 step by step or guide me to a great video that shows what to do with high detail?

    Thanks,
    K9inpoop

  2. #2
    Junior Member marcin888888's Avatar
    Join Date
    Jan 2009
    Posts
    13
    Sponsored Links
    Sponsored Links
    Would you like to sell it ? if so hit me up

  3. #3
    Member k9inpoop's Avatar
    Join Date
    Oct 2010
    Posts
    83
    Sponsored Links
    Sponsored Links
    Sorry I won't sell it but of I change my mind you'll be the first to know ok? I just need to know if its possible to fix if I get an e3 using my back ups of my nor flash created from multiman

  4. #4
    Senior Member babyjoe00069's Avatar
    Join Date
    Jul 2008
    Posts
    192
    Sponsored Links
    Sponsored Links
    i have a 60gig ps3 fat backwards compatible still on firmware 3.15 as well as a 80 gig backwards compatible ps3 phat on same low firmware. Id be willing to sale if allowed. Offers welcomed ps3s are in mint condition 80 gig still in the box.

  5. #5
    Junior Member marcin888888's Avatar
    Join Date
    Jan 2009
    Posts
    13
    first of all you must be sure that back up is clean no bad blocks, you can always check it in Flowrebuilder

  6. #6
    Member k9inpoop's Avatar
    Join Date
    Oct 2010
    Posts
    83
    How do I use flow builder to see if its good?

    Ok I checked the dump using flowrebuilder operation "extract a byte reversed nor dump" and got a 100% complete dump then I used HxD on it and did a statistics analysis and checked the 00's and FF's and they are is the range of a good dump so do I need to check anything else to see if its a good dump?
    Last edited by k9inpoop; 09-08-2012 at 05:15 PM Reason: Automerged Doublepost

  7. #7
    Junior Member marcin888888's Avatar
    Join Date
    Jan 2009
    Posts
    13
    e3, install, solder tristate point on mobo and flash your back up

  8. #8
    Member k9inpoop's Avatar
    Join Date
    Oct 2010
    Posts
    83
    Where is the tristate point on the motherboard?

    Can you show me a pic of it? And do I use a certain wire to solder with or will any wire do?
    Last edited by k9inpoop; 09-08-2012 at 06:46 PM Reason: Automerged Doublepost

  9. #9
    Senior Member GotNoUsername's Avatar
    Join Date
    Feb 2007
    Posts
    319
    Has nothing to do with your HW you have a syscon brick (Syscon expects DEX FW and sees CEX FW and shuts down the system)! You need a HW flasher to fix it and yes it can be fixed by doing the right steps.

    PS: I'm no fan of the E3 at all it bricks cons ! If you can solder use Progskeet and if not you may consider spending you PS3 to someone with soldering and unbricking skills.

    If you need more assistance just PM.

  10. #10
    Junior Member pinkone's Avatar
    Join Date
    Jan 2012
    Posts
    34
    I've fixed the same problem on a nand and nor ps3 doing a Service Mode downgrade way easier than an E3. In Service Mode the ps3 will still beep the same unless it's running an Lv2diag.self.

 

Sponsored Links

Page 1 of 2 12 LastLast
Affiliates - Contact Us - PS3 Downloads - Privacy Statement - Site Rules - Top - © 2014 PlayStation 3 News