This has FAIL written all over it and please let me explain my 3 BIG reasons:
1) by the 10 sec. mark he shows us the back of the controller twice but the first time we clearly see the "button". Right after that he flips it again only this time he intentionally covers his homemade button with his thumb. Why would he have to show us the back twice unless he didnt do it right the first time, right?
2) If you pay attention to HOW he is holding the controller he holds it 2 different ways the whole time. First time he demos his ps3 he holds it very light and relaxed showing us the xmb. As soon as he starts the jailbreak you can totally tell he is holding it very firm and hard which tells me one of his fingers behind is holding the button while the ps3 loads. Immediately right after it loads the xmb he goes back to his "light and relaxed" holding (watch for it).
3) It appears he has already admitted it will take some 8 wires to mod but has he said anything about his custom "button"? I dont know about you guys but putting a button there is already a FAIL. so What if Im playing a game and I accidentally press it? Will the controller go into jailbreak mode accidentally? And finally why risk opening your controller, installing 8 wires and a homemade button when a jailbreak clone or Tensy board will do the same for only $25-$30 and no risk to the controller?
I know we are all excited but Sorry guys this is just not practical at all. Mad props to all the devs who understand this and are continually working out of their own time to a goal we could all live with.
Check this out: http://www.elotrolado.net/hilo_guia-mod-picgoove-sixaxis-ps3_1492833
PICGroove Mod PS3 SixAxis Guide
This Mod is based on a pic 18F2550 PsgrooPic with Sixaxis PS3 controller adapted to take into account that will comply with 2 main functions:
Ps3 launch debug mode without losing any original settings and also be updatable.
Clarified, as any MOD is to make use of solder on the board of control, nothing complicated, only 8 of them.
Materials:
1 Control Sixaxis PS3 (in my case I have one of a pack of 80g without vibration, worth also for the Dualshock 3 but I have not tested).
1 Pic 18F2550 and have a list to create a Picgroove both components as the programmer. In EOL there are many tutorials about it, I personally used the scheme th0rin in version 1.2, ie PSGroo 1.2.pdf. Also do you can see from this link: http://www.elotrolado.net/hilo_tutorial-psgroopic-programador-casero-esquema-elsemi_1484968_s580 a quote from our friend calvo225, follow all the steps until you have the pic set. I recommend the program developer Art2003 WinPic800
NOTE: The pin 26 has to go to ground if you selected the option LVP tab WinPIC800 Config. If not used the LVP option, not necessary.
Cable to make posts (use data cable for hard disk ide 80-wire very pratico and a single hair).
Soldering iron, tin, scissors, paste flux, etc.
Construction: We take the pic and the file previously scheduled PSGrooPIC_wBTL_HEX_V1.5.hex all legs will bend to fit it neatly into a place of control:
This is the place you got the pic goes perfect, put the legs, facing away"
And seeing where it goes our pic we took, we cut pieces of ide cable no more than 5 cm. And proceed to solder the points: 1,8,9,10,13,14,15,16,19,20,25,26 one for each point. Remember that the pic is looking out the points 15,16,19,20, 25 and 26 are below the pic and would have to fold them up, nothing complicated for the other points is easier as they are in the superior.
Now we have to weld all the components necessary for the Pic:
Using pieces of ide cable to connect a pic, the theme of Jumper and DC outputs, D +, D-and NRM leave enough cable about 10 cm or so to be comfortable installation whether to cut it short. The LED do not place out and I do not think it takes, now if someone wants to put it, in this photo show more or less as it should be before welding something I also can find another way to put to me was the best I found:
CLARIFICATION:
Before welding something in command must prove that pic works correctly I connect to the outputs VCC, D +, D-and NRM a USB connector and see if I tore the exploit, if all goes well we proceed to the step of welding at the helm, the points are marked with colors that are welded to the plate as is without changing anything.
See diagram that goes as everything goes online are simple welds, in the part of JUMPER must draw the two lines and put in the right stick button (THIS IS TO UPDATE THE PIC FOR FUTURE UPDATES PSGROOVE).
In the top right Note that there is an extension of the RESET button I have long, I've added a switch and that is adapted to the control unit had to use a Dremel to fit it and leave it outside (this is the most important of all that the action cancels any usb functionality sends ushering in the Exploit). Authorities recommend any place to plug insulators between the wires, the pic and mini usb connector to ensure proper operation.
Operation:
To start the Xploit just put the usb cable to the console and controller, having previously turned off and the console on the back button after having pressed the RESET button and then press the POWER button then the button to activate Ejeta DEBUG , wait until you leave the logo of the console, you can remove the knob and press the PS button (the middle of the panel with the initials PS, look for games and you'll see two folders that indicate that everything went well.
To update the PIC must have these programs installed on your PC:
3. HIDbootloader.exe which is responsible for programming the pic, put the usb cable on the remote simultaneously have tightened RESET button and left stick button (reset button is to disable any USB activity in the control and the left analog stick makes its way to activate the bootloader mode of the pic) and have fulfilled that is enough to install the other end of the usb cable to pc.
The program will automatically detect the device. The same is done at the beginning of the Institute prior to installation on the remote to program. Hex of the exploit, the program's interface is very easy to interpret.
Note: do this only when we have a new update for Pic, we must take into account that you have installed the latest updates and we can play without a disc inside (in some cases there are games that deserve it.)
Well so far all for now, I hope for something to serve this project for me has been very encouraging to have done it despite the bad reviews I've had thanks to all who supported me and the team of Eol.
lol...the avg joe...heck even slightly above avg joe would probably be better off with the normal jailbreak procedures. interesting mod though, building the jailbreak device into the controller, not what we hoped for lol. i think the extra button added due to the mod could hav been better placed though, then again, i have not seen the insides of the six axis.
This has FAIL written all over it and please let me explain my 3 BIG reasons:
if i read your post, then i see that YOU are FAIL. this is your first post on this forum and you flame a project who is not classified as fake or real.
you write something about soldering on a controller is FAIL on your third reason. did you ever mentioned that this chip is worth around 1€? the cables also are worth around 50cent. for all the components to make a jailbreak controller. you have to pay 1,50€.
comparing to the 30-170euro for a jailbreak usb key /clone / what ever. this 1.50€ are great.
a little tip from mine, don't post such retarded posts, if you don't know about soldering, the efficience of those technics. and even don't post that with your first post here. this let you looks like a kid who only wanna talk with the big guys about things you don't understand.
Cfw - mfw - ofw ? - 21m ago 
Originally Posted by Dahaka801
Reply With Quote
